2,187
edits
Difference between revisions of "Installation (ESX)"
Jump to navigation
Jump to search
Added "Vmkernel Log Analysis"
(Renamed "Password Complexity Disable" to "Password Complexity Override") |
(Added "Vmkernel Log Analysis") |
||
| Line 39: | Line 39: | ||
#* EG <code>./emcgrab.sh</code> | #* EG <code>./emcgrab.sh</code> | ||
# Results can be found in <code>\emcgrab\outputs</code> folder | # Results can be found in <code>\emcgrab\outputs</code> folder | ||
== Vmkernel Log Analysis == | |||
=== Storage Monitor Log Entries === | |||
How to decode the following type of entries... | |||
Sep 3 15:15:14 tfukesxent1 vmkernel: 85:01:23:01.532 cpu4:2264)StorageMonitor: 196: vmhba1:2:0:0 status = 2/0 0x6 0x2a 0x1 | |||
Sep 3 15:15:32 tfukesxent1 vmkernel: 85:01:23:19.391 cpu4:2253)StorageMonitor: 196: vmhba1:3:9:0 status = 2/0 0x6 0x2a 0x1 | |||
The status message consists of the follow four decimal and hex blocks... | |||
{| cellpadding="4" cellspacing="0" border="1" | |||
|- | |||
|''Device Status'' / ''Host Status'' || ''Sense Key'' || ''Additional Sense Code'' || ''Additional Sense Code Qualifier'' | |||
|} | |||
Where the ESX Device and SAN host status' mean... | |||
{| cellpadding="4" cellspacing="0" border="1" | |||
|- | |||
! Decimal !! Device Status !! Host Status | |||
|- | |||
| 0 || No Errors || Host_OK | |||
|- | |||
| 1 || || Host No_Connect | |||
|- | |||
| 2 || Check Condition || Host_Busy_Busy | |||
|- | |||
| 3 || || Host_Timeout | |||
|- | |||
| 4 || || Host_Bad_Target | |||
|- | |||
| 5 || || Host_Abort | |||
|- | |||
| 6 || || Host_Parity | |||
|- | |||
| 7 || || Host_Error | |||
|- | |||
| 8 || Device Busy || Host_Reset | |||
|- | |||
| 9 || || Host_Bad_INTR | |||
|- | |||
| 10 || || Host_PassThrough | |||
|- | |||
| 11 || || Host_Soft_Error | |||
|- | |||
| 24 || Reservation Conflict || | |||
|} | |||
Where the Sense Key mean... | |||
{| cellpadding="4" cellspacing="0" border="1" | |||
|- | |||
! Hex !! Sense Key | |||
|- | |||
| 0x0 || No Sense Information | |||
|- | |||
| 0x1 || Last command completed but used error correction | |||
|- | |||
| 0x2 || Unit Not Ready | |||
|- | |||
| 0x3 || Medium Error | |||
|- | |||
| 0x4 || Hardware Error | |||
|- | |||
| 0x5 || ILLEGAL_REQUEST (Passive SP) | |||
|- | |||
| 0x6 || LUN Reset | |||
|- | |||
| 0x7 || Data_Protect - Access to data is blocked | |||
|- | |||
| 0x8 || Blank_Check - Reached an unexpected region | |||
|- | |||
| 0xa || Copy_Aborted | |||
|- | |||
| 0xb || Aborted_Command - Target aborted command | |||
|- | |||
| 0xc || Comparison for SEARCH DATA unsuccessful | |||
|- | |||
| 0xd || Volume_Overflow - Medium is full | |||
|- | |||
| 0xe || Source and Data on Medium do not agree | |||
|} | |||
The Additional Sense Code and Additional Sense Code Qualifier mean | |||
{| cellpadding="4" cellspacing="0" border="1" | |||
|- | |||
! Hex !! Sense Code | |||
|- | |||
| 0x4 || Unit Not Ready | |||
|- | |||
| 0x3 || Unit Not Ready - Manual Intervention Required | |||
|- | |||
| 0x2 || Unit Not Ready - Initializing Command Required | |||
|- | |||
| 0x29 || Device Power on or SCSI Reset | |||
|} | |||
[[Category:VMware]] | [[Category:VMware]] | ||